Front-load washer and top-load washer side by side in a laundry room

Whirlpool

Whirlpool Appliance Repair in San Jose, CA

Copy the Whirlpool code before unplugging, because a power cut clears it. That code tells the tech which part to test first.

Mainstream brand

Whirlpool

  • 2-in-1 Removable Agitator Washers
  • Front Load Laundry
  • All-In-One Washer & Dryer
  • Stacked Laundry Centers
  • French Door Refrigerators
  • Slide-In Ranges

Every Whirlpool fault comes as a pair: an F number naming the system and an E number naming the specific problem, and both vanish from the display once the power is cut. San Jose Appliance Care sends registered, insured appliance techs to San Jose homes for Whirlpool appliance repair on Cabrio and newer top-load washers with the 2-in-1 removable agitator, front-load and all-in-one washer-dryers, stacked laundry centers, French door refrigerators, dishwashers and slide-in ranges. On a Whirlpool washer, F8 covers incoming water, F9 draining, F5 the lid or door lock and F7 the motor. Homes in nearby cities like Mountain View and Sunnyvale are covered as well.

Whirlpool washer stuck on F8E1, F9E1 or F5E2

F8E1, which can also show as LF or Lo FL, means the washer doesn’t sense enough water coming in. The tech starts with both faucets, kinks in the hoses, the inlet screens and the water inlet valve. Anti-flood devices fitted to the hoses get a look too, since Whirlpool lists them as a cause.

The drain can trigger F8E1 as well. Whirlpool wants the drain hose pushed no more than 4.5 inches into a standpipe that stands at least 39 inches high. Shove it in deeper and it siphons water away as fast as the valve lets it in.

F9E1 is a drain that’s taking too long. On a top-loader, that same siphon can cause it, along with kinks, clogs or tape sealing the hose to the pipe. Front-loaders add the drain pump filter and the little drain holes in the door seal to the list, and then the drain pump itself.

F5E1 is the door switch: the control can’t confirm the door is shut. Whirlpool’s first checks are a door that isn’t fully closed and laundry or packing material blocking the switch. If it returns with the door clear, the switch and lock get tested.

F5E2 says the lid lock can’t engage, and Whirlpool puts that down to something in the way of the lock. For F7 E1 on a front-loader that was just installed, Whirlpool’s first check is the shipping bolts and spacers in the back. If F5E3 or F7E1 keeps returning, Whirlpool’s own help pages end at a service request. Both codes lead to parts that need testing, the lock assembly in one case and the motor system in the other. On a Cabrio top-loader, uL means an unbalanced load. The washer tries to even the load out before the final spin, and Whirlpool’s guide says to call for service if the code comes back. On ordinary loads that means the suspension and the drive get checked. A Whirlpool washer that leaks, grinds or won’t spin with no code on the display is covered under washer repair.

Whirlpool fridge compressor failed in year four

The standard Whirlpool limited warranty lasts one year from the original purchase date and covers factory-specified parts and labor for defects in materials or workmanship. Refrigerators get longer. Whirlpool’s 2021 refrigerator warranty covers the sealed refrigeration system on French door bottom mount and side-by-side models, parts and labor, in years two through five. That system is the compressor, evaporator, condenser, dryer and connecting tubing. So a compressor on one of those models that quits in year four is a covered repair.

If your Whirlpool is inside one of those terms, say so on the call and keep the receipt close. Outside them, the tech diagnoses the fault first, and you get the price in writing first. You only pay for work you agreed to. A Whirlpool fridge running warm with no code at all is covered under refrigerator and freezer repair.

Ice on the freezer floor or water under the crispers

The defrost drain is the usual suspect. Whirlpool places it at the back of the freezer, and when it clogs, meltwater backs up into the fridge and can run out past the bottom of the door seal. Food packed against the back wall can block it too. Ice that looks clear can be a frozen drain, while a drain that keeps refreezing points to the defrost system, which the tech tests.

Water pressure is the local detail that matters most on a Whirlpool. Whirlpool sets an upper limit for its dishwashers and for fridges with ice makers, and some Milpitas addresses run above it by the city’s own figures. Hollow cubes, a slow dispenser or a fill code that comes and goes can start at the supply line. The Milpitas appliance repair page has the numbers, so mention your city on the call. An ice maker that’s stopped altogether is covered under ice maker repair.

Check Vent, F4 E3 or AF on a Whirlpool dryer

To Whirlpool, F4 E3, AF and the words Check Vent all say one thing: air isn’t getting out of the dryer fast enough. A full lint screen can do it, and so can a vent that’s clogged, crushed, kinked or bent through too many turns. Whirlpool says to clean the whole vent run every one to two years, whether a warning has come up or not.

A stacked laundry center tucked into a hallway closet needs space around it, because the tech has to pull the unit out to reach the vent connection behind. Tell us if that’s your setup. When the vent checks out clear and the drum still runs cold, the job turns to heat. On an electric Whirlpool that means the element and its fuses. On a gas model it’s the igniter and the gas valve coils. The thermal fuse is a one-time safety part, per Whirlpool: once it blows from overheating it can’t be reset, and on many models the dryer won’t run at all. Since overheating blew it, the vent gets checked along with the new fuse. Both repairs are explained on the dryer repair page.

Whirlpool dishwasher blinking a code or holding water

A Whirlpool dishwasher with no display blinks its code out instead. Count the flashes before the pause for the F number and the flashes after it for the E number. Seven flashes, a pause, then one flash is F7E1. Do the counting before anyone shuts off the power.

On a dishwasher, F9E1 is a long drain, the same idea as on the washer. The tech goes through the filter, the drain hose, the air gap and the drain pump. On a new install, the knockout plug in the garbage disposal gets checked to make sure it came out. F1E1 points at the control, F2E1 at a key stuck on the panel and F7E2 at the wash motor. The dishwasher repair page explains what each of those visits involves.

F2 E0, F3 E0 or F9 on a Whirlpool range

On a Whirlpool range, F2 E0 points at the keypad and F3 E0 at the oven temperature sensor. With either one, don’t count on the oven holding its setting until the part has been tested. F9 can mean the supply wires went on the wrong way round, so mention the install date if the range went in within roughly the last three months.

A gas Whirlpool oven that’s slow to preheat, or lights late, points the tech to the igniter. Whirlpool says the igniter has to glow bright orange before the gas valve opens, and it lists a dirty or failing igniter among the usual causes of a gas oven that won’t heat. Whirlpool’s remaining codes, and other brands’ codes, are in the appliance error code library.

Whirlpool has recalled two kitchen products. Glass cooktops with touch controls, built from December 2016 to July 2019 under the Whirlpool, KitchenAid and JennAir names, were recalled because elements could switch on unprompted. Microwave hood combinations sold from January 2014 to April 2016, models WMH53520C and WMH73521C, were recalled over internal arcing that could set a plastic part alight. Unplug one of those microwaves and stop using it. A recalled cooktop should be shut off at the breaker whenever it’s not in use. In both cases, read us the model number when you call. A Whirlpool microwave that runs without heating, and other cooktop and microwave symptoms, are covered under cooktop and microwave repair.

Whirlpool warranty terms in brief

Standard limited warranty
1 year from first purchase, factory-specified parts and labor
Refrigerator sealed system
Parts and labor in years 2 to 5 on French door bottom mount and side-by-side models
To claim it
Proof of purchase with the model and serial number
Refrigerator water filter
30 days

Whirlpool resets, vents and warranty questions

My Whirlpool dryer is brand new. Why does it say Check Vent already?

Because the warning measures airflow, and a new dryer can sit on an old problem. A crushed transition hose behind it, or lint left in an existing wall run, will trip it on the first load. Tell us when the dryer was installed and how the vent gets outside.

Does the Whirlpool refrigerator warranty cover the water filter?

For 30 days only. After that it falls outside Whirlpool's refrigerator warranty. If the dispenser is slow even with a fresh filter in, the tech checks the water inlet valve and the supply line.

How do I reset a Whirlpool washer showing a code?

Write the code down first, because a power cut clears it. Then unplug the washer, or switch off its breaker, for five minutes, which is the reset Whirlpool gives for its door-switch code. If the same code comes back on the next cycle, the part behind it needs testing, so call with the model number.

My Whirlpool oven takes forever to preheat. Is that normal?

Whirlpool puts a normal preheat to 350°F at about 12 to 15 minutes for an oven with a visible bake element, and around 20 minutes with a hidden one. Racks left inside and a 208-volt supply add time. Much longer than that, or a gas oven that's slower than it used to be, is worth a call.

Will Whirlpool's warranty pay for spoiled food if the fridge fails?

No. Food loss is one of the exclusions in Whirlpool's limited warranty, even in the first year. The less time a warm fridge sits, the less food you lose, so call as soon as you notice it.

Whirlpool washer halted mid-cycle on an F code?

Your tech tests the part named by the code's second half, with the price down on paper before anything is replaced.

Call (669) 205-6920