A leak code is the first Thermador message to act on, though it’s far from the only one. San Jose Appliance Care takes Thermador appliance repair calls in San Jose for dishwashers, Freedom column refrigerators and freezers, single and double wall ovens, and ranges and rangetops with Star burners. Have the model number and the display message ready. Thermador’s codes separate a drain pump fault from low house voltage, a door sensor or a heater circuit, and a code read out on the phone gives a registered, insured tech a starting point. Thermador owners in Cupertino and Mountain View reach us on the same line.
Thermador dishwasher stopped with E15
Thermador defines E15 as the safety switch sensing water in the base of the dishwasher, which switches on the leak protection system. The four-digit code E3100 reports the same fault. The machine has shut itself down because water got into the base pan, which means something inside the cabinet is leaking.
Keep the dishwasher’s water valve closed until the leak is found. On the call, say when the code first came up, whether any water has reached the floor, and whether the dishwasher was moved or reinstalled lately.
E12 through E8000 on a Thermador dishwasher
Thermador sorts its dishwasher codes by the system each one points to, and a lot of the four-digit codes repeat a fault that already has a short code.

| Code | Thermador’s meaning |
|---|---|
| E12, E2060 | Limescale built up in the heat pump |
| E14, E3000 | Flow meter failure, or trouble filling with water |
| E16, E17 | Trouble with water coming in or with the fill system |
| E18 | Water level too low, or water not pumping as it should |
| E22, E24, E25 | More than one cause, including a kinked hose, a clogged air gap, or a filter or drain pump that’s blocked |
| E23, E6101 | Drain pump blocked, clogged or faulty |
| E27, E9001 | Supply voltage reaching the dishwasher is too low |
| E2120, E2130 | Fault in the zeolite (CrystalDry) chamber heater or its fan motor |
| E6160 | The Zone Control lower spray arm can’t find its home position |
| E8000 | Fault in the door sensor circuit |
A pair of these point past the machine. E27 and E9001 say the house isn’t sending the dishwasher enough voltage, so the circuit that feeds it gets checked first. E12 means scale, and the groundwater San Jose Water supplies is hard (our dishwasher repair page has the local numbers), so let us know how often that code returns.
For the board, heater and sensor codes, Thermador gives one answer: if the code comes back after a reset, the dishwasher needs service. Note the code and how far into the cycle the dishwasher got, and say which line it is. Thermador’s current dishwashers come as Star Sapphire, Sapphire and Emerald, and the Star Sapphire and Sapphire carry the third rack Thermador calls the Adjustable Chef’s Tool Drawer, so a rack or drawer complaint goes to a different parts list.
Clicking or no flame on a Star burner
Some clicking is normal. With Thermador’s ExtraLow feature on, the flame cycles off and back on, and Thermador says the igniter clicks with each relight, roughly every 60 seconds. A draft moving across the kitchen can cause clicks as well.
Other clicking points to a fault. Thermador ties burners that keep clicking to ports that are wet or packed with food. A cap sitting crooked on the star-shaped base leads to burners that won’t light or that burn tall and uneven. When a burner clicks any time its knob is on but never lights, Thermador blames wiring at the outlet and says to shut the main gas supply until it’s repaired. Burners that won’t start at all can trace back to the gas supply, or to a regulator that went in wrong.
Say whether it’s one burner or every burner, and whether you have a Professional range or a Masterpiece cooktop. Burner symptoms common to other brands are under oven, range and stove repair.
Second oven stalling around 175°F
When the second cavity of a Thermador double wall oven won’t climb past 175°F, Thermador’s explanation is either too little amperage on that circuit or a vent opening that’s blocked. Tell us which cavity it is, because the first oven can heat normally while the second one stalls.
Thermador names a few more oven faults that call for a repair visit:
- An “E” with a number on the display while the control beeps is a fault code, and if it keeps returning the oven needs service.
- A blank display with the oven light still working needs a visit.
- A broiler that cuts out early and won’t come back on most likely needs service.
Steam ovens follow the same rule as the wall ovens: Thermador publishes no list of what each “E” number means, only that a code that keeps returning after a reset needs a service visit. Read it to us exactly.
Two recalls touch these appliances. In 2010, Thermador recalled about 37,000 built-in double ovens (models C272B, C302B, SEC272, SEC302, SECD272 and SECD302) because gaps in the insulation could let the self-clean cycle overheat the cabinets around them, and owners were told not to run self-clean until the oven was inspected. In 2015, dishwashers made from 2008 to 2013 were recalled over a power cord that could overheat, and the recall grew in 2017 to more models. If yours is among them, stop using it until it’s fixed, and have the model and serial number from its plate ready for the call.
Induction cooktop zone not heating, or an F code
Thermador’s induction codes split into heat, connection and setup faults. F2, E8207 and E8208 say the electronics overheated and switched that zone off. F5, flashing with the power level and a tone, means a hot pan is sitting near the controls. E9000 and E9010 point to a zone that overheated. E7010 is a Wi-Fi or hood connection that won’t link, and dE with the zones staying cold means the cooktop isn’t connected the way the wiring diagram calls for. F8 with an H means the zones aren’t heating, and Thermador lists demo mode, a lost hood or Wi-Fi link, a weak cooking-sensor battery and the wrong supply voltage as causes. Read us the code and the model number; any code not on Thermador’s list needs a tech.
Warm Freedom column or slow ice production
Each Freedom column has its own sealed system and is set flush with the cabinetry, often behind custom panels. A fridge column and a freezer column installed as a pair are still two independent units, so name the one that’s misbehaving.

Thermador sets an ice benchmark for its refrigeration. Once the unit is cold, the ice maker should turn out 70 to 120 cubes in 24 hours, and it takes 72 hours from power-on to reach full production. If a settled column makes far less than that, or runs warm, book a repair. Thermador encodes the series in the sixth digit of a refrigerator model number, so read us the full number. Warm-fridge and ice symptoms that cross brands are on our refrigerator and freezer repair page.
Which Thermador parts stay covered, and for how long
Every Thermador category gets two years of coverage, with longer, narrower terms on built-in refrigerators and dishwashers.
| Period | Coverage |
|---|---|
| Years 1 to 2, every appliance | Parts and labor on the entire appliance |
| Years 3 to 6, built-in refrigerators | Parts and labor on the sealed system (compressor, condenser, evaporator, dryer/strainer, tubing) |
| Years 7 to 12, built-in refrigerators | Those sealed-system parts, parts only |
| Years 2 to 5, dishwashers | Parts only on the racks and the electronics (circuit board or microprocessor) |
| Lifetime | Parts only if rust eats through a fridge’s inner liner or stainless door, or a dishwasher’s stainless door or inner tub |
Terms can vary by model. If your Thermador could still be inside one of them, mention it on the call. Outside the warranty, the price goes on paper first, and you only pay for work you agreed to. The appliance repair cost guide covers what drives a built-in repair up.
