Electrolux puts the Frigidaire name on three lines: plain Frigidaire, Gallery and Professional. San Jose Appliance Care books Frigidaire repair in San Jose for all of them, from gas, electric and air fry ranges to column fridges, side-by-sides, built-in dishwashers and top-load washers. When an oven overheats, a door won’t release after self-clean or a dishwasher halts with a code, Frigidaire’s guides give that fault a number. The number points the tech toward a part before anyone arrives. Read us the line and the model off the rating label, since Frigidaire’s recall notices and warranty terms are written by line and model. We take calls from San Jose and the cities around it, Fremont and Milpitas among them.
F10 and a Frigidaire oven that bakes hot
F10 is Frigidaire’s thermal runaway code: the cavity got hotter than the setting allows. If the oven is a stone-baked pizza model, Frigidaire’s first suspect is a Pizza Shield that isn’t sitting in rack position 7. Otherwise the tech checks two things, the temperature sensor and the control that cycles the bake element or burner, since one of them is letting heat build unchecked.
The rest of Frigidaire’s range codes come down to this:
- F30 or F31: an open or shorted temperature probe circuit.
- F1, F3, F12, F13, F20 or F26: a keypad, communication or control fault. The tech tests the keypad and the control board, and leaves the heating parts alone.
Range symptoms on gas and electric models from other brands are on the oven, range and stove repair page.
Frigidaire gas and smooth-top ranges on recall
In March 2026, Frigidaire, Gallery and Professional gas ranges sold between June 2025 and January 2026 were recalled. Their bake burner can light late. Smooth-top electric ranges from the same three lines, sold from 2001 to 2009, went on recall again in 2024 because surface elements can switch on by themselves or fail to switch off.
If you have one of the recalled gas ranges, don’t use the oven until it’s repaired. For either recall, read us the serial number when you call.
Oven door still locked an hour after self-clean
A Gallery range runs self-clean for two, three or four hours, per its manual. About 15 seconds in, the latch engages, and it holds for close to an hour once the cycle is over so the cavity can cool. If the latch is still holding well past that, or F90 to F94 shows up, look at the lock motor, the lock switch and the control behind them. Those get tested on a cold oven. Give us a rough time for when the clean finished.
Frigidaire fridge not cooling, or a side-by-side with no ice
Check the door seal before anything else. Frigidaire’s test is to close the door on a paper dollar: if it slides out easily, the seal is weak, and a weak seal makes the temperature swing. After a power outage, Frigidaire says the fridge needs about 24 hours to settle back to temperature, so give it a day before deciding it’s failed.
When a side-by-side stops making ice, rule out the control lock first. It blocks ice and water until it’s held for 3 seconds. Frigidaire puts normal output at roughly 2 to 3 pounds a day. Below that with a cold freezer, the tech checks the water inlet valve, the fill tube, the ice maker and the auger in the bin.
Garage fridges are where Frigidaire gets particular. It doesn’t recommend a standard model anywhere the temperature drops below 55°F, and sells Garage Ready models for the spaces that do. San Jose garages swing both ways, from winter nights in the low 40s to a record summer heat wave, as the garage fridge section covers. Say where the fridge stands when you call.
H, DI SP or 77 on a Frigidaire fridge
On a Frigidaire fridge, H or HI says the cabinet has sat too warm for longer than an hour. Door seals come first on the visit, then the fans, the defrost parts and finally the sealed system. DI SP is ice stuck in the chute, which puts the bin, the auger and the little dispenser door on the list. 77 means demo mode is turned on.
PF shows after an outage or a surge, and per Frigidaire it can set off the high-temp alarm too, so tell us if the lights went out lately. The door alarm is meant to chime after five minutes with a door open. Chiming with everything closed sends the tech to the door switches and the control board. If the fridge is warm and the display is blank of codes, see the refrigerator and freezer repair page.
Coverage on a Frigidaire fridge is short. The 2019 and 2021 manuals list one year of parts and labor counted from the day it was bought, and the sealed system shares that same year. Spec sheets for some Professional columns go further, at two years on parts and two on labor. Say up front if your fridge is under a year old, or a Professional column younger than two.
Gallery dishwasher not drying
Some wet dishes are expected. Frigidaire says plastics, wooden items and bowls with a hollow bottom may not dry fully, and the Air Dry setting and quick cycles leave more water behind than Heat Dry. Rinse aid does the most: Frigidaire’s guide lets you raise the amount, from L0 to L6, through the control panel, and it wants the water heater at 120°F or higher.
When the dishes are still dripping on Heat Dry with rinse aid set high, the tech checks the heating element and the vent and fan that clear the moist air.
i20 with water left in the dishwasher
i20 means the dishwasher didn’t drain. The tech works through Frigidaire’s list of causes in order:
- the disposal knockout plug, on a new install
- a drain hose that’s blocked or pinched
- a hose loop that doesn’t rise at least 32 inches above the floor
- a clogged glass trap and filter
- the drain pump
A clogged sump or filter brings up i40. CL or Cd is an unlatched door. Some messages only look like trouble. Hd or HO means the machine is heating its water first, and LOC is the door lock. PF follows a power cut, and PRESS START scrolling across is a five-second reminder to shut the door. For pumps and leaks on any make, there’s the dishwasher repair page.
E1, E2 or E4 on a Frigidaire top-load washer
Slow filling brings up E1, and the visit runs from the lid to the faucets and hose screens, then on to the inlet valve. Slow draining brings up E2. Frigidaire blames the standpipe height, a bent or plugged drain hose or the breaker before it gets to the pump. E3 is the lid, open or failing to lock.
An unbalanced load is E4, and Frigidaire’s washer makes three attempts to even it out on its own before giving up. On a newly installed machine, shipping foam still in place or feet that aren’t level will trigger it. Washer problems without a code are on the washer repair page.
Frigidaire dryer running but not heating
An electric Frigidaire runs on two house breakers, and with one tripped the drum turns while the heater stays off. Frigidaire’s other checks are the setting, since Air Fluff tumbles with no heat, and the supply: a 208-volt outlet stretches drying time by about 20% compared with 240. On a gas model, the gas valve has to be open.
Past those, the heating element, the thermostats and the thermal limiter get tested. Frigidaire says a thermal limiter on an electric dryer is a part for a service provider to replace, and the vent run gets checked with it, as on the dryer repair page.
Any of these codes ends the same way: a registered, insured tech diagnoses it and hands you a written number, and you only pay for work you agreed to. An aging Frigidaire facing an expensive part is a decision the repair or replace guide walks through. Price drivers are in the appliance repair cost guide.
